Reasons Your fiat remote key 500 Key Fob Won't Work

A fiat 500x key fob 500 key fob allows you to easily open doors and start your vehicle. There are a myriad of reasons why the fob may stop working. This includes a dead battery or water damage, issues with the receiver module, and interference.

This listing is for a new key for fiat 500 replacement fiat ducato key (click through the up coming web page) Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local locksmiths for automotive locksmiths). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Key fobs of today have a limited range of operation and must be within a few inches of the vehicle in order to work. If you are not within your car and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a reputable brand like Panasonic Duracell or Energizer. They are usually available in your local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The car will flash its parking lights and the key fob will operate the lock and unlock switches.

If your fob's key does not work after replacing the battery, it may be water damage that hinders it from connecting to the module inside your vehicle. Water damage can happen in a number of ways, ranging from an accidental splash to submerging your fob in salt water at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to pull the moisture back out. If this doesn't work, your fob will probably need to be reset by an experienced locksmith or dealer.

Water Damage

While the fob comes with rubber seals that keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then cease to function. If you get the fob wet, it's not a good idea however, if you drop it into a cup of water or do not remember to take it out of your pants pocket prior to running the washing machine, don't give up hope.

First, remove the battery. Before replacing the battery clean the electronic chip with isopropyl or another similar product. Then check the fob to see if it works. If the key still doesn't work, it may need to be programmed again. This is typically done by a professional or dealer auto locksmith.

If your key is old and has not been programmed to work with your vehicle it is necessary to replace it completely. A professional locksmith for cars will be able to complete this process. The locksmith will need the key cut to match your car's ignition. The locksmith will also have to reprogram your fob into the vehicle's system. This how much is a new fiat 500 key a simple and cost-effective process that is usually completed the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob won't be working is that it's simply out of range. The remote typically has an area of 30 feet or less, and if it's too far away from your car it will not respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob isn't working It could be because of an internal circuit board problem. Reprogramming the fob is usually the solution to the issue. You can find the procedure for most vehicles on YouTube or in the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they lose tension, they could stop the coin battery from being seated properly and cause the remote to malfunction.

In rare instances, the fob can become out of the vehicle's sync because of hardware or software issues. This could cause a significant headache, but you can usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob. In some instances they might need to reinstall the software in your body control module as well.

Interference

Interference can also cause the key fob to be unable to receive or transmit the signal. This can happen when the key fob is located near a radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob may not function due to a poor connection to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. battery replacement, reprogramming and using the spare key for fiat 500 key fob, it could have a damaged receiver module on your 500. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then processed by the vehicle.

There is a straightforward method to reset the 500's on-board system including the keyfob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electrical charge, and then restart the car's computer. This will help you get your key fob to function again. If the problem persists you should seek out an expert technician. They'll be able to diagnose the exact cause of your problems.