Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to professional auto locksmiths who have the appropriate tools and know-how. They can design and program keys faster and less expensive than dealers.

If the key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking and will not allow you to start the engine. If this is the scenario, you'll need apply the backup starting technique that is detailed in your vehicle's owner manual.

The spark plugs may also be worn out. The spark plugs are responsible to ignite the fuel which starts the engine. They only last for a certain amount of time. They'll eventually break down if they aren't used frequently enough.

Fortunately, there's an easy solution for this problem. Verify the voltage of your battery using a multimeter. If it's less than 11.5 volts and you are not satisfied, then it is time to replace it. It is also important to clean the contacts of the battery in case it is corroded. This can be done by lifting the rubber covers that protect both battery terminals and using wire brushes to clean any corroded components of the battery. After that, you need to connect the positive and negative pole cables.

Water Damage

If your 208 will not start and the battery has not failed, you should examine the spark plugs. It could be that they are dirty and don't spark. This can be fixed easily by cleaning the spark plugs in an workshop.

Peugeot cars use keys that are transponder-type and is compatible with the car's immobiliser system. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the proper signal to the vehicle.

Water damage is a frequent cause of this problem. This is most common in colder climates where the vehicle could have been exposed to rain or snow. In this instance, you should contact a reliable locksmith who will have the tools and equipment needed to modify the key. They also have the latest technological know-how and machinery required to create a peugeot 207 new key programming 208 smart key. The process shouldn't take longer than 15 minutes.

Faulty battery contacts

Peugeot replaced the old transponder chips by introducing a new type that uses electronic components mounted on a circuitboard. The new system works great when it's new, but the circuit boards degrade over time and cease to function properly.

This could stop the immobiliser chip from triggering the immobiliser chip, causing your car not to start. If this happens it's recommended to call a Peugeot specialist or locksmith.

Another issue that is common is when the key fob battery gets depleted, which causes the key blade to stop from entering the lock. A car locksmith will replace the battery and then cut a new blade for you. This is a quick solution.

Faulty Receiver Module

It could be that the receiver module is malfunctioning if your peugeot key programming key fob isn't working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver module is responsible for transmitting radio frequencies to the onboard computer that controls the central locking system of your peugeot rcz key vehicle.

The key fob itself is fitted with rubber seals to prevent water from getting to the electronic chip inside. However prolonged exposure to water can penetrate these seals and damage the chip. The high salt content of the pool or ocean waters could cause damage to the key fob if it is submerged.

The module must be replaced if your Peugeot spare key no longer works. This is only done by an peugeot expert key fob specialist or expert auto locksmith. Peugeot keys like other cars are protected by an immobilizer system. This requires the correct code to begin the car. This is why it is imperative that you should only trust the Peugeot locksmith to create and program the replacement.

Computers with faulty on-board computers

The computer on board of your peugeot boxer key fob is responsible for a variety of systems in your car, including power windows and airbags. When something goes wrong with these systems, they will usually display a code that indicates the issue. This code is stored in the system and will stay there until the issue has been resolved. This can often mean that the on-board computers to be replaced.

One of the most frequent causes of the light turning on is loose or corroded connections within the airbag sensor. It can be due to wear and tear, ageing or exposure to moisture and salt. This issue should be addressed as soon as you can, as an airbag that is not functioning could be dangerous in the event of an accident.

If your Peugeot is showing a card not detected error, then the key battery inside the key fob might be weak or dead. This will stop the key fob sending a signal to deactivate your vehicle's immobilizer. Try this by pressing the unlock key on the key fob, and then trying to start your vehicle. If this fails, then the key battery must be replaced.